Broad range of sensors, CO2 meters, data loggers ,
portable instruments and monitoring systems

You have no items in your shopping cart.

Pt1000 temperature transducer (4-20mA)

Pt1000 temperature transducer (4-20mA)

  • Temperature transducer
  • Suitable for external sensors Pt1000
  • Output signal 4-20mA
  • Temperature range -100 to 30°C



staffelprijzen op aanvraag

Availability: In stock


Bel ATAL 0299-630610


The TEP-200 temperature transmitter put the signal of the Pt-1000 (platinum capacitance) sensor to a linearised 4-20 mA signal. This signal can be transported across a large distance (up to 1 kilometre) without loss of quality. This TEP-200 can be applied among other things on ATM-monitoringsystems.

The TEP-200 temperature transducer is suitable for external Pt1000 sensors. This is applicable if the cable lengths of the Pt1000 temperature sensors are longer than 10 meters. The temperature transducer has a 4-20mA output signal.

The external sensor Pt1000 should be ordered separately (see accessories).


Type: Suitable for external Pt1000/3850 ppm
Dimensions: 89x123x37 mm
Range: -100 to 30°C
Accuracy: ±0,3°C
Output signal: 4-20mA
Power: 9-30 Vdc
Protection: IP65


  1. Pt1000 temperature sensor (for contact measurments)
    • For use with ATAL ATM Plus Monitoring systems
    • Suitable for contact measurements
    • Equipped with sting sensor
  2. Pt1000 temperature sensor (for general insertion measurements with penetration probe)
    • For use with ATAL ATM Plus Monitoring systems
    • For general insertion measurements (penetration probe)
    • Equipped with sting sensor
    • Cable with silicon protection shield
  3. Pt1000 temperature sensor (for industrial insertion measurements with penetration probe)
    • For use with ATAL ATM Plus Monitoring systems
    • For industrial insertion measurements (penetration probe)
    • Equipped with penetration probe and stainless steel probe
    • Equipped with Teflon handle



For a good and efficient operation of the refrigerating equipment registration is necessary. Checking switch on / switch off times and control behavior can easily be established through registration.

Energy Management

By switching behavior of electricity consumers and increase frequency of scheduled installations the tensions, flows and cos phi could greatly vary. By registering, you will better understand the variations of voltage, current and cos phi.

Food production and distribution (HACCP)

HACCP is a hygiene code for the food industry and stands for Hazzard Analysis Critical Control Points. The biggest factor that affects the decay of food is the temperature and thereby the growth of micro-organisms

Agri- & Horticulture

Temperature and moisture differences in the greenhouse lead to production losses and a high energy consumption. Moisture and temperature sensors with high accuracy and stability are therefore an important element in ensuring the proper conditions in the greenhouse.

Health, schools and kindergardens

Research has shown that the air quality in schools and kindergartens is far below the mark. …

Data centre, telecommunication and cleanrooms

Data and telecom spaces have increasingly more difficulty to control the cooling of the established ICT equipment. Because more and more power-using computer systems can be placed in a System or 19" rack, the specific heat load rises per m2 computer room. By timely handling of heat problems costly downtime can be avoided.


In various industrial applications, the monitoring from processes are essential. Thus, for example, the pharmaceutical industry is one of the largest users of moisture measuring equipment. Most drugs are sensitive to variations in moisture levels, so this should be monitored and measured so that the finished products are consistent in quality and performance.

Laboratories (GMP / GLP)

Within a laboratory, the conditions of the room in which scientific research and experiments are kept have to fall within certain limits. In addition to the space conditions the temperature is recorded and monitored for refrigerators and freezers, CO2 braise, sterilization equipment, disinfection equipment etc.

Research and Development

Before actually a product is marketed the product is extensively tested. Parameters such as temperature, humidity, flow, pressure, power, light intensity, voltage and power consumption are much sought parameters that are easy connected on the ATAL monitoring systems.



Only registered users can write reviews. Please, log in or register